What are the installation points of the products produced by the plastic barrel manufacturers

- Jul 14, 2019-

First, we must do a good job of the basic installation

Plastic barrel manufacturers emphasize the basic requirements for the installation of large plastic drums and can withstand the corresponding pressures. For example, the gap between steel structures should not be too large, and the formwork or iron plate should be laid on it. Plastic barrel manufacturers introduce that if you want to use plastic buckets to store chemical liquids, you must have good drainage facilities and dilution devices around the site, and you need to pay attention to the bottom, because there will be a spherical crown protruding into the tank, so When installing, you should make a corresponding foundation so that you can share the weight better.

Second, we must do a good job of safety protection measures

Large plastic buckets should be safe when unloading and installation. Try to use the crane as much as possible. At the same time, the affordable plastic barrel manufacturer reminds you to remove any sharp objects or stones on the ground floor and try to unload it on the sand. Do not roll the water tank of the flange to avoid cracking of the welded part of the flange. Ya'ao carefully checks and then receives the goods. There are also plastic barrel manufacturers that also remind the plastic barrel joints are tightened at the factory, the joints may loosen during transportation, loading and unloading, so the liquid sealing of the joint sealing performance should be carried out before use.

Third, we must try to avoid leakage

It can be observed by leaking more than the joint part. If it is a plastic drum containing chemical liquid, the reliable plastic barrel manufacturer suggests that it can be leaked with water to prevent a lot of damage. The plastic barrel manufacturer also introduces that the pipe connected to the lower joint or flange of the plastic barrel should be perpendicular to the barrel. It is recommended to use rubber soft joint to avoid filling the liquid under the uneven expansion of the barrel, resulting in leakage of the joint and serious damage. Joint and barrel.

The above are several installation points of the products produced by the plastic barrel manufacturer. In addition, when the inlet port is higher from the bottom of the plastic storage tank, the inlet port should be bent into the tank to make the liquid fall along the tank wall to reduce the impact on the bottom. When the plastic barrel manufacturer introduces a heavier auxiliary equipment such as a mixer on the barrel, or the worker must work on the top of the tank and cannot bear the weight of the person, please make another shelf or ladder and pay attention to the safety of the work.

5. What are the installation points of the products produced by the plastic barrel manufacturers?

In industrial production, plastic drums must be used and properly installed according to the specifications, which can facilitate the transportation or storage of related products. Especially for plastic drums with larger models, plastic barrel manufacturers think that they should pay more attention to Master the following installation points to ensure that the relevant construction or transportation work can proceed smoothly.

First, we must do a good job of the basic installation

Plastic barrel manufacturers emphasize the basic requirements for the installation of large plastic drums and can withstand the corresponding pressures. For example, the gap between steel structures should not be too large, and the formwork or iron plate should be laid on it. Plastic barrel manufacturers introduce that if you want to use plastic buckets to store chemical liquids, you must have good drainage facilities and dilution devices around the site, and you need to pay attention to the bottom, because there will be a spherical crown protruding into the tank, so When installing, you should make a corresponding foundation so that you can share the weight better.

Second, we must do a good job of safety protection measures

Large plastic buckets should be safe when unloading and installation. Try to use the crane as much as possible. At the same time, the affordable plastic barrel manufacturer reminds you to remove any sharp objects or stones on the ground floor and try to unload it on the sand. Do not roll the water tank of the flange to avoid cracking of the welded part of the flange. Ya'ao carefully checks and then receives the goods. There are also plastic barrel manufacturers that also remind the plastic barrel joints are tightened at the factory, the joints may loosen during transportation, loading and unloading, so the liquid sealing of the joint sealing performance should be carried out before use.

Third, we must try to avoid leakage

It can be observed by leaking more than the joint part. If it is a plastic drum containing chemical liquid, the reliable plastic barrel manufacturer suggests that it can be leaked with water to prevent a lot of damage. The plastic barrel manufacturer also introduces that the pipe connected to the lower joint or flange of the plastic barrel should be perpendicular to the barrel. It is recommended to use rubber soft joint to avoid filling the liquid under the uneven expansion of the barrel, resulting in leakage of the joint and serious damage. Joint and barrel.

The above are several installation points of the products produced by the plastic barrel manufacturer. In addition, when the inlet port is higher from the bottom of the plastic storage tank, the inlet port should be bent into the tank to make the liquid fall along the tank wall to reduce the impact on the bottom. When the plastic barrel manufacturer introduces a heavier auxiliary equipment such as a mixer on the barrel, or the worker must work on the top of the tank and cannot bear the weight of the person, please make another shelf or ladder and pay attention to the safety of the work.

 www.fhpails.com